BSA

For the BSA Brigadier airrifle we have a pressure regulator available that can be placed into the pressure tube.
This regulator is vented to the atmosphere without any modification to your pressure tube. So no drilling in the tube and also no creeping up in power.

The benefits:

Higher accuracy of your rifle due to the elimination of the pelletspeed fluctuations
A constant pellet speed over the full working pressure range.
It will give you a better shotcount and a full flat shotstring immediately.
Adding a regulator to your airrifle will probably give you the biggest benefit in the tuning process.
Often the rifle will make less noise due to better balance in air usage 


When you order one of our regulators you will receive:

• Your regulator preset on to your own wishes;
• A pressure scale in Bar’s on the regulator, for fine-tuning or re-adjustment;
• We will include a “Huma regulated” breech sticker;
• Fitting instructions as pdf download

 
Pressure settings

The regulators come in the standart middle pressure range (MP: 70-150 bar output) covering sub 12 ft/lbs and FAC models.
They come preset on the most common pressure setting, or we will adjust it according to your personal wishes.
It is also equipped with a clear pressure scale label, so you can very easy re-adjust or fine tune the pressure setting suitable to your wishes.


Quality

The regulator is CNC produced out of high grade aircraft Aluminum and bronze.
To guarantee a perfect product, every regulator is manually assembled, tested and adjusted to the requested pressure. 
We only use belleville springs designed for critical applications to achieve the highest repeat accuracy. This gives our regulators a repeat cycle less than 1% difference.

For the new BSA Buccaneer SE we have designed a pressure regulator that can be pushed into the pressure tube.
This regulator is vented to the atmosphere without any modification to your pressure tube. So no drilling in the tube and also no creeping up in power.

The benefits:

Higher accuracy of your rifle due to the elimination of the pelletspeed fluctuations
A constant pellet speed over the full working pressure range.
It will give you a better shotcount and a full flat shotstring immediately.
Adding a regulator to your airrifle will probably give you the biggest benefit in the tuning process.
Often the rifle will make less noise due to better balance in air usage 


When you order one of our regulators you will receive:

• Your regulator preset on to your own wishes;
• A pressure scale in Bar’s on the regulator, for fine-tuning or re-adjustment;
• We will include a “Huma regulated” breech sticker;
• Fitting instructions as pdf download

 
Pressure settings

The regulators come in the standart middle pressure range (MP: 70-150 bar output) covering sub 12 ft/lbs and FAC models.
They come preset on the most common pressure setting, or we will adjust it according to your personal wishes.
It is also equipped with a clear pressure scale label, so you can very easy re-adjust or fine tune the pressure setting suitable to your wishes.


Quality

The regulator is CNC produced out of high grade aircraft Aluminum and bronze.
To guarantee a perfect product, every regulator is manually assembled, tested and adjusted to the requested pressure. 
We only use belleville springs designed for critical applications to achieve the highest repeat accuracy. This gives our regulators a repeat cycle less than 1% difference.

 

 

Before ordering a regulator:
Please make sure, you have made yourself familiar with the fitting instructions on our website, you are happy to carry out the necessary work and you are able to adjust your power to keep your rifle legal.
Gamo/BSA pressure tubes can be rough inside. Please make sure your pressure tube is smooth and free of scraches, if not, please remove the scratches and polish the inner wall before installing the regulator for proper sealing of the regulator o-rings

This Huma regulator is specialy designed for tuning your BSA Goldstar target airrifle.

It’s very easy to install on your rifle, just depressurize the rifle, unscrew the pressure tube and replace the original regulator for the Huma tuning regulator and your are finished. *

The benefits of this regulator:

- Easy to adjust and finetune due to the clear pressure scale. 
- This regulator has a wide pressure range to cover all calibers
- Excellent consistency
- Higher accuracy of your rifle due to the elimination of the pellet speed fluctuations
 

When you order one of our regulators you will receive:

• Your regulator preset on to your own wishes;
• A pressure scale in Bar’s on the regulator, for fine-tuning or re-adjustment;
• We will include a “Huma regulated” breech sticker;

Pressure settings

The regulator comes preset on the most common pressure setting, or we will adjust it according to your personal wishes.
It is also equipped with a clear pressure scale label, so you can very easy re-adjust or fine tune the pressure setting suitable to your wishes.

Due to his length, this reg has a restricted airvolume, so this makes it specially suitable for the 12 ft/lbs – 16 Joule versions. The maximum power of the reg is about 25 ft/lbs – 35 Joule with a 47 cm barrel. If you are looking for a higher power regulator for your BSA mmc rifle please take a look at our high power internal regulator
 

 
Quality

The regulator is CNC produced out of high grade aircraft Aluminum and bronze.
To guarantee a perfect product, every regulator is manually assembled, tested and adjusted to the requested pressure. 
We only use belleville springs designed for critical applications to achieve the highest repeat accuracy. This gives our regulators a repeat cycle less than 1% difference.

This unique regulator is specially designed as a "one on one" replacement regulator for the BSA R10 rifles and solves all your regulator problem instantly!
It can be screwed into the action within a minute. It fit’s all models.
The regulator is vented to the atmosphere, so no creeping up in power in long term.

The regulator is very consistent over the total pressure range of the buddy bottle and solves all the known issues of the original regulator.
Made of high grade aircraft aluminium in combination with  CR42 molybdeen steel.

Designed for a wide pressure range (70-150 bar) to suit sub 12 ft/lbs (UK) and  high power FAC models.
 

The benefits:

Higher accuracy of your rifle due to the elimination of the pelletspeed fluctuations
A constant pellet speed over the full working pressure range.
It will give you a better shotcount and a full flat shotstring immediately.


Pressure settings

The regulator comes preset on the most common pressure setting according to your choise of barrel and caliber, or we will adjust it according to your personal wishes.
The length of the barrel is measured from the magazine until the tip of the actual barrel (not the end of the shroud)
After fitting the regulator, always check the powersetting of the rifle and finetune it when needed to stay within legal limits.


When you order one of our regulators you will receive:

• Your regulator preset on to your own wishes;
• We will include a “Huma regulated” breech sticker;
• Fitting instructions as pdf download

 
Quality

The regulator is CNC produced out of high grade aircraft Aluminum and bronze.
To guarantee a perfect product, every regulator is manually assembled, tested and adjusted to the requested pressure. 
We only use belleville springs designed for critical applications to achieve the highest repeat accuracy. This gives our regulators a repeat cycle less than 1% difference.

HuMa hatsan regulator.
Voor de BSA hebben we een regulator ontworpen welke zonder aanpassingen te doen aan het wapen direct in de drukbuis kan worden gezet. Zonder boren of andere modificaties kan deze regulator door een goede wapenmaker vlot worden gemonteerd. Zelf doen? Geen probleem, we leveren een goede instructie op aanvraag mee.

Let erop, vermeld je caliber en de gewenste druk. Weet u de gewenste druk niet? Meld ons dan op welke afstand u graag wilt schieten en met welke kracht.

For the BSA (also called hammerli pneuma)  we have designed a regulator what can be slided into the pressure tube. This regulator is vented to the atmosphere without any modification to your pressure tube. So no drilling in the tube and also no creeping up in power. The regulator is CNC produced out of high grade 7075 Aluminium. Every regulator is manually assembled, tested and adjusted to the requested pressure. Of course the regulator can be easily adjusted up or down in pressure if needed.
They are available for .22 and .25. .177 is possible on special request.

This regulator is specialy designed for tuning your BSA Scorpion and BSA scorpion T10 airrifle.

It’s very easy to install on your rifle, just depressurize the rifle, unscrew the pressure tube and screw the regulator between valvehouse and pressure tube and your are finished.*

We copied the original BSA valve body thread to allow the body of the regulator to be screwed directly to the valve body and air cylinder.
Important to know that the regulator ads 36 mm of length to the pressure tube.
When you have a Scorpion with a 320 mm long pressure tube you can probably still fit a HW silencer. For the other models BSA’s please check if your silencer will still fit the rifle when the regulator is placed. You will probably need a 27 mm silencer.

The benefits of this regulator over other regulators currently on the market:

Higher accuracy of your rifle due to the elimination of the pelletspeed fluctuations
A constant pellet speed over the full working pressure range.
It will give you a better shotcount and a full flat shotstring immediately.The regulator housing is made of extremely tough 42Cr steel,
Tested for a working pressure of at least 3x the working pressure of the rifle, for everyone’s safety,
It uses a long stroke piston that gives great consistency.
The regulator body and the housing are one piece, so no chance of the regulator moving inside the cylinder,
The one piece body and regulator housing also reduces the possibility of leaks,
The regulator piston is captive and does not need any adjustment or extra work to keep it in place,
DIY fitting is a real option for the most people,
High quality bluing, same colour as the original BSA pressure tube,
Adding a regulator to your airrifle will probably give you the biggest benefit in the tuning process.

When you order one of our regulators you will receive:

• Your regulator preset on to your own wishes;
• A pressure scale in Bar’s on the regulator, for fine-tuning or re-adjustment;
• We will include a “Huma regulated” breech sticker;
• Fitting instructions as pdf download

Pressure settings

The regulator comes preset on the most common pressure setting, or we will adjust it according to your personal wishes.
It is also equipped with a clear pressure scale label, so you can very easy re-adjust or fine tune the pressure setting suitable to your wishes.

Due to his length, this reg has a restricted airvolume, so this makes it specially suitable for the 12 ft/lbs – 16 Joule versions. The maximum power of the reg is about 25 ft/lbs – 35 Joule with a 47cm. barrel. If you are looking for a high power regulator for your BSA mmc rifle please take a look at our high power internal regulator

* Please remove the brass restrictor part out of the valvehouse and check if your transferport is between 4 - 4,5 mm. Otherwise open it up for best performance

 
Quality

The regulator is CNC produced out of high grade aircraft Aluminum and bronze.
To guarantee a perfect product, every regulator is manually assembled, tested and adjusted to the requested pressure. 
We only use belleville springs designed for critical applications to achieve the highest repeat accuracy. This gives our regulators a repeat cycle less than 1% difference.

For the BSA Sportsman we have a special internal pressure regulator what can be screwed on top of the original valve house and will be seated inside the pressure tube.
Due this unique design this regulator is vented to the atmosphere without any modification to your pressure tube. So no drilling in the tube and also no creeping up in power.
This model is specially desiged for the high power versions.

The benefits:

Higher accuracy of your rifle due to the elimination of the pelletspeed fluctuations
A constant pellet speed over the full working pressure range.
It will give you a better shotcount and a full flat shotstring immediately.
Adding a regulator to your airrifle will probably give you the biggest benefit in the tuning process.
Often the rifle will make less noise due to better balance in air usage 


When you order one of our regulators you will receive:

• Your regulator preset on to your own wishes;
• A pressure scale in Bar’s on the regulator, for fine-tuning or re-adjustment;
• We will include a “Huma regulated” breech sticker;
• Fitting instructions as pdf download

 
Pressure settings

The regulator comes preset on the most common pressure setting, or we will adjust it according to your personal wishes.
It is also equipped with a clear pressure scale label, so you can very easy re-adjust or fine tune the pressure setting suitable to your wishes.


Quality

The regulator is CNC produced out of high grade aircraft Aluminum and bronze.
To guarantee a perfect product, every regulator is manually assembled, tested and adjusted to the requested pressure. 
We only use belleville springs designed for critical applications to achieve the highest repeat accuracy. This gives our regulators a repeat cycle less than 1% difference.

 

 

Before ordering a regulator:
Please make sure, you have made yourself familiar with the fitting instructions on our website, you are happy to carry out the necessary work and you are able to adjust your power to keep your rifle legal.
Gamo/BSA pressure tubes can be rough inside. Please make sure your pressure tube is smooth and free of scraches, if not, please remove the scratches and polish the inner wall before installing the regulator for proper sealing of the regulator o-rings.

This regulator is specialy designed for tuning your BSA Scorpion and BSA scorpion T10 airrifle.

It’s very easy to install on your rifle, just depressurize the rifle, unscrew the pressure tube and screw the regulator between valvehouse and pressure tube and your are finished.*

We copied the original BSA valve body thread to allow the body of the regulator to be screwed directly to the valve body and air cylinder.
Important to know that the regulator ads 36 mm of length to the pressure tube.
When you have a Scorpion with a 320 mm long pressure tube you can probably still fit a HW silencer. For the other models BSA’s please check if your silencer will still fit the rifle when the regulator is placed. You will probably need a 27 mm silencer.

The benefits of this regulator over other regulators currently on the market:

Higher accuracy of your rifle due to the elimination of the pelletspeed fluctuations
A constant pellet speed over the full working pressure range.
It will give you a better shotcount and a full flat shotstring immediately.The regulator housing is made of extremely tough 42Cr steel,
Tested for a working pressure of at least 3x the working pressure of the rifle, for everyone’s safety,
It uses a long stroke piston that gives great consistency.
The regulator body and the housing are one piece, so no chance of the regulator moving inside the cylinder,
The one piece body and regulator housing also reduces the possibility of leaks,
The regulator piston is captive and does not need any adjustment or extra work to keep it in place,
DIY fitting is a real option for the most people,
High quality bluing, same colour as the original BSA pressure tube,
Adding a regulator to your airrifle will probably give you the biggest benefit in the tuning process.

When you order one of our regulators you will receive:

• Your regulator preset on to your own wishes;
• A pressure scale in Bar’s on the regulator, for fine-tuning or re-adjustment;
• We will include a “Huma regulated” breech sticker;
• Fitting instructions as pdf download

Pressure settings

The regulator comes preset on the most common pressure setting, or we will adjust it according to your personal wishes.
It is also equipped with a clear pressure scale label, so you can very easy re-adjust or fine tune the pressure setting suitable to your wishes.

Due to his length, this reg has a restricted airvolume, so this makes it specially suitable for the 12 ft/lbs – 16 Joule versions. The maximum power of the reg is about 25 ft/lbs – 35 Joule with a 47cm. barrel. If you are looking for a high power regulator for your BSA mmc rifle please take a look at our high power internal regulator

* Please remove the brass restrictor part out of the valvehouse and check if your transferport is between 4 - 4,5 mm. Otherwise open it up for best performance

 
Quality

The regulator is CNC produced out of high grade aircraft Aluminum and bronze.
To guarantee a perfect product, every regulator is manually assembled, tested and adjusted to the requested pressure. 
We only use belleville springs designed for critical applications to achieve the highest repeat accuracy. This gives our regulators a repeat cycle less than 1% difference.

For the Bsa Ultra SE models we have designed an unique regulator what replaces the original “body adaptor” part of the rifle.
It’s made of Chrome Molybdeen steel what is blued so it has the same finish as the original BSA part.

Designed for a wide pressure range (70-150 bar) to suit sub 12 ft/lbs (UK) and  high power FAC models.

After the regulator is placed the pressure gauge still indicates the fill pressure of the main pressure tube.
It’s very easy to install on your rifle, just depressurize the rifle, unscrew the body adapter en screw the regulator in it’s place and your are finished.
The regulator is vented to to the atmosphere without the need of drilling a hole or what so ever. This guaranties very consistent regulating behavior without creeping up in pellet speed during time!

 

The benefits of this regulator over other regulators currently on the market:

Higher accuracy of your rifle due to the elimination of the pelletspeed fluctuations
A constant pellet speed over the full working pressure range.
It will give you a better shotcount and a full flat shotstring immediately.
Adding a regulator to your airrifle will probably give you the biggest benefit in the tuning process.
The regulator housing is made of extremely tough 42Cr steel,
Tested for a working pressure of at least 3x the working pressure of the rifle, for everyone’s safety,
It uses a long stroke piston that gives great consistency.
The regulator body and the housing are one piece, so no chance of the regulator moving inside the cylinder,
DIY fitting is a real option for the most people,
High quality bluing, same colour as the original BSA pressure tube,

When you order one of our regulators you will receive:

• Your regulator preset on to your own wishes;
• We will include a “Huma regulated” breech sticker;
• Fitting instructions as pdf download

Pressure settings

The regulator comes preset on the most common pressure setting, or we will adjust it according to your personal wishes.
 

Quality

The regulator is CNC produced out of high grade materials like 42Cr steel and bronze.
To guarantee a perfect product, every regulator is manually assembled, tested and adjusted to the requested pressure. 
We only use belleville springs designed for critical applications to achieve the highest repeat accuracy. This gives our regulators a repeat cycle less than 1% difference.


Before ordering a regulator:
Please make sure, you have made yourself familiar with the fitting instructions on our website, you are happy to carry out the necessary work and you are able to adjust your power to keep your rifle legal.
* Please remove the brass restrictor part out of the valvehouse and check if your transferport is between 4 - 4,5 mm. Otherwise open it up for best performance

For the new BSA Ultra XL  model we have designed a pressure regulator that can be pushed into the pressure tube.
This regulator is vented to the atmosphere without any modification to your pressure tube. So no drilling in the tube and also no creeping up in power.

The benefits:

Higher accuracy of your rifle due to the elimination of the pelletspeed fluctuations
A constant pellet speed over the full working pressure range.
It will give you a better shotcount and a full flat shotstring immediately.
Adding a regulator to your airrifle will probably give you the biggest benefit in the tuning process.
Often the rifle will make less noise due to better balance in air usage 


When you order one of our regulators you will receive:

• Your regulator preset on to your own wishes;
• A pressure scale in Bar’s on the regulator, for fine-tuning or re-adjustment;
• We will include a “Huma regulated” breech sticker;
• Fitting instructions as pdf download

 
Pressure settings

The regulators come in the standart middle pressure range (MP: 70-150 bar output) covering sub 12 ft/lbs and FAC models.
They come preset on the most common pressure setting, or we will adjust it according to your personal wishes.
It is also equipped with a clear pressure scale label, so you can very easy re-adjust or fine tune the pressure setting suitable to your wishes.


Quality

The regulator is CNC produced out of high grade aircraft Aluminum and bronze.
To guarantee a perfect product, every regulator is manually assembled, tested and adjusted to the requested pressure. 
We only use belleville springs designed for critical applications to achieve the highest repeat accuracy. This gives our regulators a repeat cycle less than 1% difference.

 

 

Before ordering a regulator:
Please make sure, you have made yourself familiar with the fitting instructions on our website, you are happy to carry out the necessary work and you are able to adjust your power to keep your rifle legal.
Gamo/BSA pressure tubes can be rough inside. Please make sure your pressure tube is smooth and free of scraches, if not, please remove the scratches and polish the inner wall before installing the regulator for proper sealing of the regulator o-rings.