BSA

Huma-Air BSA Brigadier Tuning Regulator
For the BSA Brigadier airrifle we have a pressure regulator available that can be placed into the pressure tube. This regulator is vented to the atmosphere without any modification to your pressure tube. So no drilling in the tube and also no creeping up in power.

The benefits

• Higher accuracy of your rifle due to the elimination of the pelletspeed fluctuations.
• A constant pellet speed over the full working pressure range.
• It will give you a better shotcount and a full flat shotstring immediately.
• Adding a regulator to your airrifle will probably give you the biggest benefit in the tuning process.
• Often the rifle will make less noise due to better balance in air usage.

Pressure settings
The regulators come in the standart middle pressure range (MP: 70-150 bar output) covering sub 12 ft/lbs and FAC models. They come preset on the most common pressure setting, or we will adjust it according to your personal wishes. It is also equipped with a clear pressure scale label, so you can very easy re-adjust or fine tune the pressure setting suitable to your wishes.

Huma-Air Quality Control
Huma-Air regulators are CNC produced out of high grade aircraft Aluminum and bronze. To guarantee a perfect product, every regulator is manually assembled, tested and adjusted to the requested pressure. We only use high-end materials and our belleville springs are designed for critical applications to achieve the highest repeat accuracy. This gives our regulators a repeat cycle less than 1% difference.

* Gelieve hieronder aan te geven voor welk kalilber u de regulator wilt bestellen en welke setting u wilt. Als u een custom setting wilt geef dit dan aan in het opmerkingen veld. U komt dit veld vanzelf tegen als u verder gaat met bestellen. Als u de standaard setting wilt, vul dan niets in.

Huma-Air BSA Buccaneer SE Tuning Regulator
For the new BSA Buccaneer SE we have designed a tuning regulator that can be pushed into the pressure tube. This regulator is vented to the atmosphere without any modification to your pressure tube. So no drilling in the tube and also no creeping up in power.

The benefits

• Higher accuracy of your rifle due to the elimination of the pelletspeed fluctuations
• A constant pellet speed over the full working pressure range.
• It will give you a full flat shotstring immediately.
• Adding a regulator to your airrifle will probably give you the biggest benefit in the tuning process.
• Often the rifle will make less noise due to better balance in air usage 

Pressure settings
The regulators come in the standart middle pressure range (MP: 70-150 bar output) covering sub 12 ft/lbs and FAC models. They come preset on the most common pressure setting, or we will adjust it according to your personal wishes. It is also equipped with a clear pressure scale label, so you can very easy re-adjust or fine tune the pressure setting suitable to your wishes.

Huma-Air Quality Control
Huma regulator's are CNC produced out of high grade aircraft Aluminum and bronze. To guarantee a perfect product, every regulator is manually assembled, tested and adjusted to the requested pressure. We only use high-end materials and our belleville springs are designed for critical applications to achieve the highest repeat accuracy. This gives our regulators a repeat cycle less than 1% difference.

* Gelieve hieronder aan te geven voor welk kalilber u de regulator wilt bestellen en welke setting u wilt. Als u een custom setting wilt geef dit dan aan in het opmerkingen veld. U komt dit veld vanzelf tegen als u verder gaat met bestellen. Als u de standaard setting wilt, vul dan niets in.

Huma-Air regulator specialy designed for tuning your BSA Goldstar target airrifle
It’s very easy to install on your rifle, just depressurize the rifle, unscrew the pressure tube and replace the original regulator for the Huma tuning regulator and you are finished.*

The benefits

• Easy to adjust and finetune due to the clear pressure scale. 
• This regulator has a wide pressure range to cover all calibers
• Excellent consistency
• Higher accuracy of your rifle due to the elimination of the pellet speed fluctuations

Pressure settings
The regulator comes preset on the most common pressure setting, or we will adjust it according to your personal wishes. It is also equipped with a clear pressure scale label, so you can very easy re-adjust or fine tune the pressure setting suitable to your wishes.
Due to his length, this reg has a restricted airvolume, so this makes it specially suitable for the 12 ft/lbs – 16 Joule versions. The maximum power of the reg is about 25 ft/lbs – 35 Joule with a 47 cm barrel. If you are looking for a higher power regulator for your BSA mmc rifle please take a look at our high power internal regulator

Huma-Air Quality Control
Huma-Air regulators are CNC produced out of high grade aircraft Aluminum and bronze. To guarantee a perfect product, every regulator is manually assembled, tested and adjusted to the requested pressure. We only use high-end materials and our belleville springs are designed for critical applications to achieve the highest repeat accuracy. This gives our regulators a repeat cycle less than 1% difference.

* Gelieve hieronder aan te geven voor welk kalilber u de regulator wilt bestellen en welke setting u wilt. Als u een custom setting wilt geef dit dan aan in het opmerkingen veld. U komt dit veld vanzelf tegen als u verder gaat met bestellen. Als u de standaard setting wilt, vul dan niets in.

Huma-Air BSA R10 Tuning Regulator
This unique BSA R10 tuning regulator is specially designed as a "one on one" replacement regulator for the BSA R10 rifles and solves all your original regulator problems instantly. The regulator is very consistent over the total pressure range of the buddy bottle and it can be screwed into the action within a minute. It fit’s all models. The regulator is vented to the atmosphere, so no creeping up in power in long term. Designed for a wide pressure range (70-150 bar) to suit sub 12 ft/lbs (UK) and  high power FAC models.

The benefits

• Higher accuracy of your rifle due to the elimination of the pelletspeed fluctuations
• A constant pellet speed over the full working pressure range.
• It will give you a better shotcount and a full flat shotstring immediately.
• The pressure scale will give you the posibilty to adjust the output pressure of the R10 regulator very easy

Pressure settings
The regulator comes preset on the most common pressure setting according to your choise of barrel and caliber, or we will adjust it according to your personal wishes. The pressure range is adjustable from 70-150 bar. The length of the barrel is measured from the magazine until the tip of the actual barrel (not the end of the shroud). After fitting the regulator, always check the powersetting of the rifle and finetune it when needed to stay within legal limits.

Huma-Air Quality Control
Huma regulator's are CNC produced out of high grade aircraft Aluminum and bronze. To guarantee a perfect product, every regulator is manually assembled, tested and adjusted to the requested pressure. We only use high-end materials and our belleville springs are designed for critical applications to achieve the highest repeat accuracy. This gives our regulators a repeat cycle less than 1% difference.

* Gelieve hieronder aan te geven voor welk kalilber u de regulator wilt bestellen en welke setting u wilt. Als u een custom setting wilt geef dit dan aan in het opmerkingen veld. U komt dit veld vanzelf tegen als u verder gaat met bestellen. Als u de standaard setting wilt, vul dan niets in.

BSA Scorpion 1200 SE External Tuning Regulator
For the scorpion .25 SE models and the Scorpion SE 1200 models we have model regulator available specially for the real power lovers.
This external regulator screws between pressure tube and gauge assembly.

The difference compared to the normal BSA "SE" regulator is that this regulator uses the original pressure gauge body what gives it a lot more regulated volume. So it is specialy made for the .25 scorpion 1200 SE rifle or .22 with extreme power levels.
After assembling, the pressure gauge will indicate the regulated power. It’s very easy to install on your rifle, just depressurize the rifle, unscrew the pressuretube and screw the regulator in it’s place and your are finished.*

For the Scorpion 1200 SE in .177 and .22 you can also choose the BSA "SE" regulator.

The benefits

• The regulator housing is made of extremely tough 42Cr steel,
• Tested for a working pressure of at least 3x the working pressure of the rifle, for everyone’s safety,
• DIY fitting is a real option for the most people,
• High quality bluing, same colour as the original BSA pressure tube,
• Higher accuracy of your rifle due to the elimination of the pelletspeed fluctuations
• A constant pellet speed over the full working pressure range.
• It will give you a better shotcount and a full flat shotstring immediately.
• Adding a regulator to your airrifle will probably give you the biggest benefit in the tuning process.

Pressure settings
The regulator comes preset on the most common pressure setting, or we will adjust it according to your personal wishes. It is also equipped with a clear pressure scale label, so you can very easy re-adjust or fine tune the pressure setting suitable to your wishes.

Huma-Air Quality Control
The regulator is CNC produced out of high grade aircraft Aluminum and bronze. To guarantee a perfect product, every regulator is manually assembled, tested and adjusted to the requested pressure. We only use belleville springs designed for critical applications to achieve the highest repeat accuracy. This gives our regulators a repeat cycle less than 1% difference.

* Gelieve hieronder aan te geven voor welk kalilber u de regulator wilt bestellen en welke setting u wilt. Als u een custom setting wilt geef dit dan aan in het opmerkingen veld. U komt dit veld vanzelf tegen als u verder gaat met bestellen. Als u de standaard setting wilt, vul dan niets in.

Huma-Air BSA Scorpion Internal Tuning Regulator
For the BSA Scorpion we have a special internal pressure regulator what can be screwed on top of the original valve house and will be seated inside the pressure tube. Due to this unique design this regulator is vented to the atmosphere without any modification to your pressure tube. So no drilling in the tube and also no creeping up in power. This model is specially designed for the high power models.

The benefits

• Higher accuracy of your rifle due to the elimination of the pelletspeed fluctuations.
• A constant pellet speed over the full working pressure range.
• It will give you a better shotcount and a full flat shotstring immediately.
• Adding a regulator to your airrifle will probably give you the biggest benefit in the tuning process.
• Often the rifle will make less noise due to better balance in air usage.

Pressure settings
Designed for a wide pressure range (70-150 bar) to suit sub 12 ft/lbs (UK) and  high power FAC models. The regulator comes preset on the most common pressure setting, or we will adjust it according to your personal wishes. It is also equipped with a clear pressure scale label, so you can very easy re-adjust or fine tune the pressure setting suitable to your wishes.

Quality
The regulator is CNC produced out of high grade aircraft Aluminum and bronze. To guarantee a perfect product, every regulator is manually assembled, tested and adjusted to the requested pressure. We only use belleville springs designed for critical applications to achieve the highest repeat accuracy. This gives our regulators a repeat cycle less than 1% difference.

Huma-Air BSA Scorpion pressure regulator (external)
This regulator is specifically designed for tuning your BSA Scorpion and BSA scorpion T10 airrifle. It’s very easy to install on your rifle. Just depressurize the rifle, unscrew the pressure tube and screw the regulator between valvehouse and pressure tube and you are finished.*

We copied the original BSA valve body thread to allow the body of the regulator to be screwed directly to the valve body and air cylinder and we designed it for a wide pressure range (70-150 bar) to suit sub 12 ft/lbs (UK) and high power FAC models.

* Important to know that the regulator ads 36 mm of length to the pressure tube.

When you have a Scorpion with a 320 mm long pressure tube you can probably still fit a HW silencer. For the other models BSA’s please check if your silencer will still fit the rifle when the regulator is placed. You will probably need a 27 mm silencer.

The benefits

• Higher accuracy of your rifle due to the elimination of the pelletspeed fluctuations.
• A constant pellet speed over the full working pressure range.
• It will give you a better shotcount and a full flat shotstring immediately.The regulator housing is made of extremely tough 42Cr steel.
• Tested for a working pressure of at least 3x the working pressure of the rifle, for everyone’s safety.
• It uses a long stroke piston that gives great consistency.
• The regulator body and the housing are one piece, so no chance of the regulator moving inside the cylinder.
• The one piece body and regulator housing also reduces the possibility of leaks.
• The regulator piston is captive and does not need any adjustment or extra work to keep it in place.
• DIY fitting is a real option for the most people.
• High quality bluing, same colour as the original BSA pressure tube.
• Adding a regulator to your airrifle will probably give you the biggest benefit in the tuning process.

Pressure settings
The regulator comes preset on the most common pressure setting, or we will adjust it according to your personal wishes. It is also equipped with a clear pressure scale label, so you can very easy re-adjust or fine tune the pressure setting suitable to your wishes.

Due to his length, this reg has a restricted airvolume, so this makes it specially suitable for the 12 ft/lbs – 16 Joule versions. The maximum power of the reg is about 25 ft/lbs – 35 Joule with a 47cm. barrel. If you are looking for a high power regulator for your BSA mmc rifle please take a look at our high power internal regulator

* Please remove the brass restrictor part out of the valvehouse and check if your transferport is between 4 - 4,5 mm. Otherwise open it up for best performance.

Huma-Air Quality Control
The regulator is CNC produced out of high grade aircraft Aluminum and bronze. To guarantee a perfect product, every regulator is manually assembled, tested and adjusted to the requested pressure. We only use belleville springs designed for critical applications to achieve the highest repeat accuracy. This gives our regulators a repeat cycle less than 1% difference.

* Gelieve hieronder aan te geven voor welk kalilber u de regulator wilt bestellen en welke setting u wilt. Als u een custom setting wilt geef dit dan aan in het opmerkingen veld. U komt dit veld vanzelf tegen als u verder gaat met bestellen. Als u de standaard setting wilt, vul dan niets in.

Huma-Air BSA Scorpion SE Tuning Regulator
For the Bsa Scorpion SE models we have designed an unique regulator what replaces the original “body adaptor” part of the rifle. It’s made of Chrome Molybdeen steel what is blued so it has the same finish as the original BSA part. Designed for a wide pressure range (70-150 bar) to suit sub 12 ft/lbs (UK) and  high power FAC models.

After the regulator is placed the pressure gauge still indicates the fill pressure of the main pressure tube. It’s very easy to install on your rifle, just depressurize the rifle, unscrew the body adapter en screw the regulator in it’s place and your are finished*The regulator is vented to to the atmosphere without the need of drilling a hole or what so ever. This guaranties very consistent regulating behavior without creeping up in pellet speed during time!

Due to the limited volume of the BSA action construction these regulators are suitable for the low- and high power version in .177 and .22.For the the .25 SE models and the SE 1200 models in high power version we have BSA SE 1200 model available

The benefits

• Higher accuracy of your rifle due to the elimination of the pelletspeed fluctuations.
• A constant pellet speed over the full working pressure range.
• It will give you a better shotcount and a full flat shotstring immediately.
• Adding a regulator to your airrifle will probably give you the biggest benefit in the tuning process.
• The regulator housing is made of extremely tough 42Cr steel.
• Tested for a working pressure of at least 3x the working pressure of the rifle, for everyone’s safety.
• It uses a long stroke piston that gives great consistency.
• The regulator body and the housing are one piece, so no chance of the regulator moving inside the cylinder.
• DIY fitting is a real option for the most people.
• High quality bluing, same colour as the original BSA pressure tube.

Pressure settings
The regulator comes preset on the most common pressure setting according to your choise of barrel and caliber, or we will adjust it according to your personal wishes. The length of the barrel is measured from the magazine until the tip of the actual barrel (not the end of the shroud). After fitting the regulator, always check the powersetting of the rifle and finetune it when needed to stay within legal limits.

Huma-Air Quality Control
The regulator is CNC produced out of high grade materials like 42Cr steel and bronze. To guarantee a perfect product, every regulator is manually assembled, tested and adjusted to the requested pressure. We only use belleville springs designed for critical applications to achieve the highest repeat accuracy. This gives our regulators a repeat cycle less than 1% difference.

* Gelieve hieronder aan te geven voor welk kalilber u de regulator wilt bestellen en welke setting u wilt. Als u een custom setting wilt geef dit dan aan in het opmerkingen veld. U komt dit veld vanzelf tegen als u verder gaat met bestellen. Als u de standaard setting wilt, vul dan niets in.

Huma-Air BSA Sportsman Tuning Regulator
For the BSA Sportsman we have a special internal pressure regulator that can be screwed on top of the original valve house and will be seated inside the pressure tube. Due to this unique design this regulator is vented to the atmosphere without any modification to your pressure tube. So no drilling in the tube and also no creeping up in power. This model is specially desiged for the high power versions.

The benefits

• Higher accuracy of your rifle due to the elimination of the pelletspeed fluctuations
• A constant pellet speed over the full working pressure range.
• It will give you a better shotcount and a full flat shotstring immediately.
• Adding a regulator to your airrifle will probably give you the biggest benefit in the tuning process.
• Often the rifle will make less noise due to better balance in air usage.

Pressure settings
The regulator comes preset on the most common pressure setting, or we will adjust it according to your personal wishes. It is also equipped with a clear pressure scale label, so you can very easy re-adjust or fine tune the pressure setting suitable to your wishes.

Huma-Air Quality Control
The regulator is CNC produced out of high grade aircraft Aluminum and bronze. To guarantee a perfect product, every regulator is manually assembled, tested and adjusted to the requested pressure. We only use belleville springs designed for critical applications to achieve the highest repeat accuracy. This gives our regulators a repeat cycle less than 1% difference.

Huma-Air BSA Scorpion pressure regulator (external)
This regulator is specifically designed for tuning your BSA Ultra MMC airrifle. It’s very easy to install on your rifle. Just depressurize the rifle, unscrew the pressure tube and screw the regulator between valvehouse and pressure tube and you are finished.*

We copied the original BSA valve body thread to allow the body of the regulator to be screwed directly to the valve body and air cylinder and we designed it for a wide pressure range (70-150 bar) to suit sub 12 ft/lbs (UK) and high power FAC models.

The benefits

• Higher accuracy of your rifle due to the elimination of the pelletspeed fluctuations.
• A constant pellet speed over the full working pressure range.
• It will give you a better shotcount and a full flat shotstring immediately.The regulator housing is made of extremely tough 42Cr steel.
• Tested for a working pressure of at least 3x the working pressure of the rifle, for everyone’s safety.
• It uses a long stroke piston that gives great consistency.
• The regulator body and the housing are one piece, so no chance of the regulator moving inside the cylinder.
• The one piece body and regulator housing also reduces the possibility of leaks.
• The regulator piston is captive and does not need any adjustment or extra work to keep it in place.
• DIY fitting is a real option for the most people.
• High quality bluing, same colour as the original BSA pressure tube.
• Adding a regulator to your airrifle will probably give you the biggest benefit in the tuning process.

Pressure settings
The regulator comes preset on the most common pressure setting according to your choise of barrel and caliber, or we will adjust it according to your personal wishes. The length of the barrel is measured from the magazine until the tip of the actual barrel (not the end of the shroud). After fitting the regulator, always check the powersetting of the rifle and finetune it when needed to stay within legal limits.

Due to his length, this reg has a restricted airvolume, so this makes it specially suitable for the 12 ft/lbs – 16 Joule versions. The maximum power of the reg is about 25 ft/lbs – 35 Joule with a 47 cm barrel. If you are looking for a higher power regulator for your BSA mmc rifle please take a look at our high power internal regulator.

* Please remove the brass restrictor part out of the valvehouse and check if your transferport is between 4 - 4,5 mm. Otherwise open it up for best performance

Huma-Air Quality Control
The regulator is CNC produced out of high grade aircraft Aluminum and bronze.
To guarantee a perfect product, every regulator is manually assembled, tested and adjusted to the requested pressure. 
We only use belleville springs designed for critical applications to achieve the highest repeat accuracy. This gives our regulators a repeat cycle less than 1% difference.

* Gelieve hieronder aan te geven voor welk kalilber u de regulator wilt bestellen en welke setting u wilt. Als u een custom setting wilt geef dit dan aan in het opmerkingen veld. U komt dit veld vanzelf tegen als u verder gaat met bestellen. Als u de standaard setting wilt, vul dan niets in.

Huma-Air BSA Ultra SE Tuning Regulator
For the Bsa Ultra SE models we have designed an unique regulator what replaces the original “body adaptor” part of the rifle. It’s made of Chrome Molybdeen steel what is blued so it has the same finish as the original BSA part. Designed for a wide pressure range (70-150 bar) to suit sub 12 ft/lbs (UK) and  high power FAC models.

After the regulator is placed the pressure gauge still indicates the fill pressure of the main pressure tube. It’s very easy to install on your rifle, just depressurize the rifle, unscrew the body adapter en screw the regulator in it’s place and your are finished. The regulator is vented to to the atmosphere without the need of drilling a hole or what so ever. This guaranties very consistent regulating behavior without creeping up in pellet speed during time!

The benefits

• Higher accuracy of your rifle due to the elimination of the pelletspeed fluctuations.
• A constant pellet speed over the full working pressure range.
• It will give you a better shotcount and a full flat shotstring immediately.
• Adding a regulator to your airrifle will probably give you the biggest benefit in the tuning process.
• The regulator housing is made of extremely tough 42Cr steel.
• Tested for a working pressure of at least 3x the working pressure of the rifle, for everyone’s safety.
• It uses a long stroke piston that gives great consistency.
• The regulator body and the housing are one piece, so no chance of the regulator moving inside the cylinder.
• DIY fitting is a real option for the most people.
• High quality bluing, same colour as the original BSA pressure tube.

Pressure settings
The regulator comes preset on the most common pressure setting, or we will adjust it according to your personal wishes.

Huma-Air Quality Control
The regulator is CNC produced out of high grade materials like 42Cr steel and bronze. To guarantee a perfect product, every regulator is manually assembled, tested and adjusted to the requested pressure. We only use belleville springs designed for critical applications to achieve the highest repeat accuracy. This gives our regulators a repeat cycle less than 1% difference.

* Gelieve hieronder aan te geven voor welk kalilber u de regulator wilt bestellen en welke setting u wilt. Als u een custom setting wilt geef dit dan aan in het opmerkingen veld. U komt dit veld vanzelf tegen als u verder gaat met bestellen. Als u de standaard setting wilt, vul dan niets in.

Huma-Air BSA Ultra XL Tuning Regulator
For the new BSA Ultra XL  model we have designed a pressure regulator that can be pushed into the pressure tube. This regulator is vented to the atmosphere without any modification to your pressure tube. So no drilling in the tube and also no creeping up in power.

The benefits

• Higher accuracy of your rifle due to the elimination of the pelletspeed fluctuations.
• A constant pellet speed over the full working pressure range.
• It will give you a better shotcount and a full flat shotstring immediately.
• Adding a regulator to your airrifle will probably give you the biggest benefit in the tuning process.
• Often the rifle will make less noise due to better balance in air usage.

Pressure settings
The regulators come in the standart middle pressure range (MP: 70-150 bar output) covering sub 12 ft/lbs and FAC models. They come preset on the most common pressure setting, or we will adjust it according to your personal wishes. It is also equipped with a clear pressure scale label, so you can very easy re-adjust or fine tune the pressure setting suitable to your wishes.

Huma-Air Quality Control
The regulator is CNC produced out of high grade aircraft Aluminum and bronze. To guarantee a perfect product, every regulator is manually assembled, tested and adjusted to the requested pressure. We only use belleville springs designed for critical applications to achieve the highest repeat accuracy. This gives our regulators a repeat cycle less than 1% difference.

* Gelieve hieronder aan te geven voor welk kalilber u de regulator wilt bestellen en welke setting u wilt. Als u een custom setting wilt geef dit dan aan in het opmerkingen veld. U komt dit veld vanzelf tegen als u verder gaat met bestellen. Als u de standaard setting wilt, vul dan niets in.